Ford FLTM BI 107-05
GMW15919
FCA LP-463PB-64-01
The Model 100-V2 Steam Generator design combines simplicity and ruggedness for ease of operation, durability at an affordable price. It produces a constant psi, high temperature wet steam at the wand outlet. This unit is designed specifically for the automotive thermal shock test.
100-V2型蒸汽發生器設計簡單耐用，易于操作，經久耐用，價格合理。它在棒出口產生恒定的psi高溫濕蒸汽。該裝置為汽車熱沖擊試驗而設計。
Power: 120V, 60Hz, 10amps
功率：120V，60Hz，10amps
Operation: 100 psi, 1.0 gpm, 340 degrees F. maximum
操作：100 psi，1.0 gpm，340華氏度，Max
Safety: pressure relief valve and high temperature shut off switch
安全：泄壓閥和高溫切斷開關
Fuel Tank Capacity: 10 US gallons
油箱容量：10美制加侖
Fuel: K1 kerosene is preferred for the machine
燃料：機器選K1煤油
Fuel Burner: 1/5 HP motor, precision fuel pressure gauge
燃油燃燒器：1/5馬力電機，精密燃油壓力表
Heating Coil: 7/8” OD x 154’ helical wound steel tubing
加熱盤管：外徑7/8“x 154”螺旋纏繞鋼管
Water Supply: tap water (garden hose fitting)
供水：自來水（軟管配件）
Water Pump: triplex oil bath pump, 3/4 HP motor
水泵：三缸油浴泵，3/4馬力電機
Water Tank: 2 Gallon stainless steel, continuous feed, float controlled
水箱：2加侖不銹鋼，連續供水，浮子控制
Front Panel Instrumentation: digital system press. meter, digital system temp. meter, real time water flow meter; water flow regulator valve, hour meter
前面板儀表：數字系統壓力機。儀表，數字系統溫度。流量計，實時水流量計；水流量調節閥，小時計
Tires: foam filled pneumatic (no flats)
輪胎：泡沫充氣（無扁平）
Pressure Wand: custom made steam wand with burst proof steam hose
壓力棒：帶有防爆蒸汽軟管的定制蒸汽棒
Thermal Shock Testing Unit Package (kit)
熱沖擊試驗裝置包（套件）
This unit is a kerosene burning steam generator designed specifically for automotive thermal shock (steam jet) testing. It is sold in a combination testing package only and contains the following list of separate components:
該裝置是一臺煤油燃燒蒸汽發生器，為汽車熱沖擊（蒸汽噴射）測試而設計。它僅在組合測試包中出售，并包含以下單獨組件列表：
Model 100-V2 w/ wand assembly (2013 redesign – Testing Innovations)
Dynamic Head Fixture (for calibrating “upon each use”)
Testing Fixture (holds test sample and TS wand in place for testing)
Cutting Fixture/Guide (for test sample scribing/cutting)
Temperature Meter/TC/Target Panel
Instructional Flash Drive
Laminated Placard – system test parameters
Calibration
The thermal shock unit and kit comes ready to ship, secured to a heavy pallet in a triple corrugated box approximately 67”x37”x61” and weighs approximately 600 lbs
1.100-V2型帶棒組件（2013年重新設計-測試創新）
2.動態頭部夾具（用于“每次使用時”校準）
3.測試夾具（將測試樣品和TS棒固定在測試位置）
4.切割夾具/導軌（用于試樣劃線/切割）
5.溫度計/TC/目標面板
6.教學閃存驅動器
7.層壓標牌-系統測試參數
8.校準
9.熱沖擊裝置和套件已準備好裝運，固定在三重瓦楞紙箱中的重型托盤上，約67“x37”x61”，重量約600磅
Thermal Shock Indoor Workstation
熱沖擊室內工作站
This workstation has an upper hood, a lower sink and areas to calibrate, cut/scribe, holding the sample during test, a discharge tube for holding the wand between sample testing and includes the following:
該工作站有一個上罩、一個下水槽和用于校準、切割/劃線的區域，在試驗過程中保持樣品，一個用于在樣品試驗之間保持棒的放電管，包括：
1.This stainless steel workstation is not designed to be
2.It is designed to be used indoors
3.It has a stainless steel upper hood and a stainless steel lower sink
4.Sample testing fixture station (uses the Testing Fixturepurchased with thermal shock unit)
5.Thermal shock wand clamping fixture (wand purchased with thermal shock unit)
6.Polycarbonate sliding safety shield for the DHP calibration compartment
7.Polycarbonate sliding safety shield for the testing compartment
8.DHP calibration zone with gauge stand (gauge purchased with thermal shock unit)
9.Test sample cutting, scribing, preparation area (guide purchased with thermal shock unit)
10.TS wand discharge tube (a place to hold the steam blasting wand between tests)
11.Hood is designed to evacuate humidity
12.Hood can be configured for evacuation of fumes and humidity (optional, at extra cost)
13.Needs tube axial fan of approximately 1200 cfm (explosion proof, approximately 12”)
14.Stand comes with adjustable feet
15.Needs to be hooked up to standard drain or position over floor drain
1.本不銹鋼工作站不設計為移動式
2.設計用于室內
3.它有一個不銹鋼上罩和一個不銹鋼下水槽
4.樣品測試夾具站（使用與熱沖擊裝置一起購買的測試夾具）
5.熱震棒夾具（與熱震裝置一起購買的熱震棒）
6.DHP校準室的聚碳酸酯滑動安全防護罩
7.用于測試室的聚碳酸酯滑動安全防護罩
8.DHP校準區，帶儀表架（儀表與熱沖擊裝置一起購買）
9.試樣切割、劃線、準備區（與熱沖擊裝置一起購買的指南）
10.TS棒排放管（在試驗之間固定蒸汽噴砂棒的位置）
11.發動機罩設計用于排出濕氣
12.可配置發動機罩以排出煙霧和濕氣（可選，額外費用）
13.需要約1200 cfm的管式軸流風機（防爆，約12”）
14.支架配有可調節的支腳
15.需要連接至標準排水管或位于地漏上方
