進口不銹鋼磁力泵 

進口不銹鋼磁力泵概述：

德國巴赫生產的進口不銹鋼磁力泵采用*設計原理與制造工藝，通過外磁體、隔離套、內磁體之間的磁場傳導，將動密封轉換為靜密封，保證泵浦高溫狀態下的穩定性工作。廣泛配套小型精密高溫模溫機、試驗儀器、木工機械、擠出等行業，泵浦移送循環介質不含顆粒、纖維、非易燃易爆的液體。進口不銹鋼磁力泵由泵、磁力傳動器、電動機三部分組成。關鍵部件磁力傳動器由外磁轉子、內磁轉子及不導磁的隔離套組成。

當電動機帶動外磁轉子旋轉時，磁場能穿透空氣隙和非磁性物質，帶動與葉輪相連的內磁轉子作同步旋轉，實現動力的無接觸傳遞，將動密封轉化為靜密封。由于泵軸、內磁轉子被泵體、隔離套*封閉，從而*解決了“跑、冒、滴、漏”問題，消除了煉油化工行業易燃、易爆、有毒、有害介質通過泵密封泄漏的安全隱患，有力地保證了職工的身心健康和安全生產。

進口磁力泵的工作原理

采用*的外混式軸向回水泵體結構設計，泵體由吸液室、儲液室、蝸殼、回流孔、氣液分離室等部份組成（結構見示意圖）。泵啟動后，在離心力的作用下，吸水室中的剩余液體與進液管路中的空氣被葉輪攪拌形成氣液混合物，混合物通過蝸殼進入氣液分離室，隨著流速降低，導致氣水分離，空氣由泵出液口排出，液體經回流孔返回泵腔內，經過多次循環，進液管道中的空氣被逐漸排空，使泵腔內形成一定的真空度，低位槽中的液體在大氣壓的作用下流向泵進口，達到自吸的作用，這一系列的自吸過程是泵在剛啟動的1至3分鐘內自動完成，無需人工干預，當液體充滿泵的進液管路與泵腔后泵組即自動進入正常運行狀態。磁力自吸泵的驅動裝置采用主動磁鐵聯軸器直接裝在電機軸上，通過磁力偶合間接驅動轉子組合上的葉輪旋轉，泵腔全部封閉，*無泄漏。同使用機械密封或填料密封的離心泵相比較，磁力泵具有以下優點：

1．泵軸由動密封變成封閉式靜密封，*避免了介質泄漏。

2．無需獨立潤滑和冷卻水，降低了能耗。

3．由聯軸器傳動變成同步拖動，不存在接觸和摩擦。功耗小、效率高，且具有阻尼減振作用，減少了電動機振動對泵的影響和泵發生氣蝕振動時對電動機的影響。

4．過載時，內、外磁轉子相對滑脫，對電機、泵有保護作用。

當磁力傳動器的從動部件在過載情況下運行或轉子卡死時，磁力傳動器的主、從動部件會自動滑脫，保護機泵。此時磁力傳動器上的永磁體在主動轉子交變磁場的作用下，將產生渦損、磁損，造成永磁體溫度升高，磁力傳動器滑脫失效。

進口不銹鋼磁力泵產品用途：

進口不銹鋼磁力泵的過流部件采用不銹鋼（304、316、316L）制成，廣泛應用于石油、化工、制藥、電鍍、環保、水處理、國防等部門，是輸送易燃、易爆、有毒和貴重液體的理想設備，是創建無泄漏、無污染文明車間的zuijia選擇。適用溫度：-20℃～100℃。

參數

進口14mm~100mm-出口10mm~80mm 流量: 1.2m3/h-60m3/h
級數: 2-10 揚程: 5m-50m 吸程: 3-6m 轉速: 2900r/m
電機功率: 0.12kw~18.5kw 適用介質:酸，堿液，油類，稀有貴重液，鍍液，揮發性液體 
電壓:220/380V  材質:不銹鋼

進口不銹鋼磁力泵應用:不含固體顆粒腐蝕液體、強酸、強堿、乙醇、漂白劑、照相液、硝酸、鹽酸、氫氟酸、醋酸、氫氧化納、丙酮、四氧乙烷、海水、鹽水等

Imported stainless steel magnetic pump

Overview of imported stainless steel magnetic pump:

Germany Bach production imported stainless steel magnetic pump adopt advanced design principle and manufacturing technology, through the outer magnet, isolation cover, inner magnet magnetic conduction between the dynamic seal into static seal, ensure the pump work stability under high temperature. It has a wide range of small precision high temperature die temperature machine, test instrument, woodworking machinery, extruding and other industries, pump transfer circulating medium without particles, fiber, non-flammable and explosive liquid. The imported stainless steel magnetic pump consists of three parts: pump, magnetic drive and motor. The key component magnetic actuator consists of an outer magnetic rotor, an internal magnetic rotor and a non-conductive isolation sleeve.

When the motor drives the outer magnetic rotor rotating magnetic field can penetrate air gap and the magnetic materials, magnetic drive is connected with the impeller in the rotor synchronous rotation, realize the power out of contact, the dynamic seal into static seal. Because of the pump body, pump shaft, the magnetic rotor of sleeve compley closed, so as to thoroughly solve the "run, run, drip, leak problem, eliminates the oil refining chemical industry flammable, explosive, toxic and harmful medium by pump seal leakage of safe hidden trouble, effectively guarantee the staff's physical and mental health and safety in production.

The working principle of imported magnetic pump

The pump body is designed by the advanced external mixing shaft to the pump body structure. The pump body is composed of the absorption chamber, the liquid storage room, the volute, the reflux hole and the separation chamber of the gas liquid. Pump starts, in under the action of centrifugal force, the remaining liquid in the suction chamber and into the air in the liquid line is impeller form gas-liquid mixture and stir the mixture enters the gas-liquid separation chamber through the volute, as the flow velocity is reduced, cause gas water separation, the air is being exhausted from port pumping liquid, liquid reflux hole to return to the pump cavity, after many cycles, into the air in the fluid pipeline is emptying gradually, make the pump cavity formed certain vacuum degree, low trough in the liquid flow under the action of atmospheric pressure, pump imports, to achieve the effect of imbibition, this series of imbibition process pump is just start in 1 to 3 minutes automatically, without human intervention, when the liquid into the liquid pipe of the pump and the pump cavity after automatically into the normal operation of the pump group. Magnetic self-priming pump driving device adopts active magnet coupling directly on the motor shaft, indirectly by magnetic coupling driving rotor combination on the impeller rotation, all closed, the pump chamber compley without leakage. Compared with the centrifugal pump that USES mechanical seal or packing seal, the magnetic pump has the following advantages:

1. The pump shaft is turned from the dynamic seal to a closed static seal, which compley avoids the leakage of the medium.

There is no need for independent lubrication and cooling water to reduce energy consumption.

3. The coupling drive becomes synchronized drag and there is no contact and friction. The power consumption is small and efficient, and it has damping and damping, which reduces the influence of the motor vibration on the pump and the vibration of the pump.

4. When overloading, the inner and outer magnetic rotor is relatively smooth and has protective effect on the motor and pump.

When the driving part of the magnetic driver is run or the rotor card dies under overload, the main and driven parts of the magnetic driver will automatically slip off and protect the pump. At this time, the permanent magnet on the magnetic drive is under the action of the active rotor alternating magnetic field, which will cause the vortex loss and magnetic loss, causing the permanent magnet temperature to rise and the magnetic transmission slip and failure.

Use of imported stainless steel magnetic pump products:

Imports of stainless steel magnetic pump flow components of stainless steel (304, 316, 316 l), which is widely used in petroleum, chemical, pharmaceutical, electroplating, environmental protection, water treatment, the defense department, is conveying inflammable, explosive, toxic and expensive liquid ideal equipment, is to create no leakage, no pollution civilization shop the best choice. Applicable temperature: - 20 ℃ ~ 100 ℃.

Imported stainless steel magnetic pump parameters

Import 14mm ~ 100mm - export 10mm ~ 80mm flow: 1.2m3 / h - 60m3 / h

Series: 2-10 lift: 5m - 50m suction range: 3-6m RPM: 2900r/m

Motor power: 0.12 kw ~ 18.5 kw applicable media: acid, alkali liquor, oil, rare precious liquid, liquid, volatile liquid

Voltage: 220/380v material: stainless steel

Imports of stainless steel magnetic pump application: not containing solid particles and corrosive liquid, strong acid, strong alkali, ethanol, bleach, photographic liquid, nitric acid, hydrochloric acid, hydrofluoric acid, acetic acid, sodium hydroxide, acetone, four oxygen ethane, seawater and brine etc