PR6423/000-031 CON041 熱控TSI大機軸振位移傳感器

產品詳情資料

EPRO振動傳感器PR6423/000-031 CON041

　　汽輪機監視系統（TSI）是一種集保護和檢測功能于一身的監視系統，是大型旋轉機械的保護系統。

　　TSI可以對機組在起動、運行過程中的一些重要參數能可靠地進行監視和儲存，它不僅能指示機組運行狀態、記錄輸出信號、實現數值越限報警、出現危險信號時使機組自動停機，同時還能為故障診斷提供數據，因而廣泛地應用于3MW～600MW的各種汽輪發電機組上。

　　一、汽輪機監視的內容

　　汽機應監視和保護的項目隨蒸汽參數的升高而增多，且隨機組不一而各有差異，一般有以下一些參數:

　　（1）軸向位移監視：連續監視推力盤到推力軸承的相對位置，以保證轉子與靜止部件間不發生摩擦，避免災難性事故的發生。當軸向位移過大時，發出報警或停機信號。

　　（2）差脹監視：連續檢測轉子相對于汽缸上某基準點（通常為推力軸承）的膨脹量，一般采用電渦流探頭進行測量，也可用線性差動位移變送器（LVDT）進行測量。

　　（3）缸脹監視：連續監測汽缸相對于基礎上某一基準點（通常為滑銷系統的死點）的膨脹量。由于膨脹范圍大，目前一般都采用LVDT進行缸脹監視。

　　（4）零轉速監視：連續監測轉子的零轉速狀態。當轉速低于某規定值時，報警繼電器動作，以便投入盤車裝置。

　　（5）轉速監視：連續監測轉子的轉速。當轉速高于設定值時給出報警信號或停機信號。

　　（6）振動監視：監視主軸相對于軸承座的相對振動和軸承座的振動。

　　（7）偏心度監視：連續監視偏心度的峰-峰值和瞬時值。轉速為1～600r/min時，主軸每轉一圈測量一次偏心度峰-峰值，此值與鍵相脈沖同步。當轉速低于1r/min時，機組不再盤車而停機，這時瞬時偏心度儀表的讀數應小，這就是轉子停車位置。

　　（8）相位監視：采用相位計連續測量選定的輸入振動信號的相位。輸入信號取自鍵相信號和相對振動信號，經轉換后供顯示或記錄。

　　（9）閥位指示：連續指示調速汽門的動作位置。

　　下表列出了一些應監視與保護的項目。

　　汽輪機組監視與保護項目一覽表

英文產品詳細信息

EPRO vibration sensor PR6423/000-031 CON041

The turbine safety monitoring system (TSI) is a monitoring system that integrates protection and detection functions, and is an essential protection system for large rotating machinery.

TSI can reliably monitor and store some important parameters of the unit during startup and operation. It can not only indicate the operating status of the unit, record output signals, achieve numerical limit exceeding alarms, and automatically shut down the unit in case of danger signals, but also provide data for fault diagnosis. Therefore, it is widely used in various steam turbine generator units ranging from 3MW to 600MW.

1、 Content of turbine safety monitoring

The items that should be monitored and protected by the steam turbine increase with the increase of steam parameters, and there are differences in random groups, generally including the following parameters:

(1) Axial displacement monitoring: Continuously monitor the relative position of the thrust disc to the thrust bearing to ensure that there is no friction between the rotor and stationary components, and to avoid catastrophic accidents. When the axial displacement is too large, an alarm or shutdown signal is issued.

(2) Differential expansion monitoring: Continuously detects the expansion of the rotor relative to a certain reference point (usually a thrust bearing) on the cylinder, usually measured using an eddy current probe or a linear differential displacement transmitter (LVDT).

(3) Cylinder expansion monitoring: Continuously monitoring the expansion of the cylinder relative to a certain reference point (usually the dead center of the sliding pin system) on the foundation. Due to the large expansion range, LVDT is currently commonly used for cylinder expansion monitoring.

(4) Zero speed monitoring: Continuously monitor the zero speed status of the rotor. When the speed drops below a specified value, the alarm relay acts in order to activate the turning gear.

(5) Speed monitoring: Continuously monitor the speed of the rotor. When the speed exceeds the set value, an alarm signal or shutdown signal is given.

(6) Vibration monitoring: Monitor the relative vibration of the spindle relative to the bearing seat and the vibration of the bearing seat.

(7) Eccentricity monitoring: continuously monitoring the peak to peak and instantaneous values of eccentricity. At a speed of 1-600r/min, the eccentricity peak to peak is measured once per revolution of the spindle, which is synchronized with the keyphase pulse. When the speed is lower than 1 r/min, the unit stops without turning, and the instantaneous eccentricity meter reading should be the smallest, which is the rotor parking position.

(8) Phase monitoring: Use a phase meter to continuously measure the phase of the selected input vibration signal. The input signal is taken from the keyphase signal and the relative vibration signal, and is converted for display or recording.

(9) Valve position indication: Continuously indicating the action position of the speed control valve.

The following table lists some items that should be monitored and protected.

List of Safety Monitoring and Protection Items for Steam Turbine Units

免責聲明：

AMIKON我們銷售新產品和停產產品，獨立渠道購買此類特色產品。阿米控不是本網站特色產品的授權分銷商、經銷商或代表。本網站上使用的所有產品名稱/產品圖片、商標、品牌和徽標均為其各自所有者的財產。帶有這些名稱,圖片、商標、品牌和徽標的產品描述、描寫或銷售僅用于識別目的，并不表示與任何權利持有人有任何關聯或授權。