通信電纜 網絡設備 無線通信 云計算|大數據 顯示設備 存儲設備 網絡輔助設備 信號傳輸處理 多媒體設備 廣播系統 智慧城市管理系統 其它智慧基建產品
深圳市銓順宏科技有限公司
深圳市銓順宏科技有限公司
藍牙AOA定位基站FU-GA25-P2是一款殼體防護等級達到IP66的高精度定位基站，采用的AOA到達角定位技術，與定位引擎和多種藍牙終端一起組成亞米級高精度實時定位系統，單臺基站即可獨立進行高精度定位。
一、藍牙AOA高精度定位基站產品介紹
藍牙AOA高精度定位基站FU-GA25-P2是一款殼體防護等級達到IP66的高精度定位基站，采用的AOA到達角定位技術，與定位引擎和多種藍牙終端一起組成亞米級高精度實時定位系統，單臺基站即可獨立進行高精度定位。
藍牙AOA高精度定位基站FU-GA25-P2定位引擎高性能，具備多架構支持、跨平臺設計、云邊融合設計的特點，軟件配置高效快速，具備覆蓋效果仿真、圖紙輸出、性能評估等技術支持優勢；
Bluetooth AOA high-precision positioning base station FU-GA25-P2 is a high-precision positioning base station with the protection level of IP66. It adopts the latest AOA angle-of-arrival positioning technology, and forms a sub-meter high-precision real-time positioning system together with positioning engines and various Bluetooth terminals, so that a single base station can independently perform high-precision positioning.
The positioning engine of FU-GA25-P2, a Bluetooth AOA high-precision positioning base station, has the characteristics of high performance, multi-architecture support, cross-platform design and cloud edge fusion design. The software configuration is efficient and fast, and it has the advantages of technical support such as coverage effect simulation, drawing output and performance evaluation.
二、藍牙AOA高精度定位基站型號名稱
產品名稱：藍牙AOA高精度定位基站
產品型號：FU-GA25-P2
產品外觀：
三、藍牙AOA高精度定位基站包裝清單
品類 | 數量 |
FU-GA25-P2 | 1 |
安裝盤架 | 1 |
合格證 | 1 |
安裝螺釘KA4*30及膠塞 | (1螺釘+1膠塞) ×4 |
防水接口4件套 | 2 |
四 、藍牙AOA高精度定位基站產品參數
4.1、藍牙AOA定位基站產品關鍵特性：
a、尺寸：180.7mm x 180.7mm x39.36mm
b、工作頻段：2.401GHz – 2.481GHz
c、工作溫度：-20℃ - 60℃
d、功耗：＜2W
e、安裝高度：≤10m
f、供電方式：標準 PoE (IEEE 802.3af/at) /DC 供電 12-30V 1A
4.2、藍牙AOA定位基站接口說明
a、RJ45 * 2：分為 PoE IN 和 PoE OUT，供電與數據傳輸接口，可通過網線與標準 PoE 交換機連接或與其他雙網口基站級聯
b、DC 接口：供電電壓與 PSE 供電的適配
c、復位孔：恢復默認設置按鍵，長按3S，基站綠燈快閃持續5S，表示基站恢復初始設置并重啟成功
A、size: 180.7mm x 180.7mm x39.36mm
B、Operating frequency band: 2.401 GHz–2.481 GHz.
C、Working temperature: -20℃-60℃
D、power consumption: < 2w
E.、Installation height: ≤10m
F、power supply mode: standard PoE (IEEE 802.3af/at) /DC power supply 12-30V1.
4.2. Description of Bluetooth AOA Positioning Base Station Interface
A, RJ45 * 2: It is divided into PoE IN and PoE OUT, which are power supply and data transmission interfaces, and can be connected with standard PoE switches through network cables or cascaded with other dual-port base stations.
B, DC interface: adaptation of power supply voltage and PSE power supply.
C. Reset hole: press and hold the button to restore the default settings for 3S, and the base station will flash green for 5S, indicating that the base station has restored its initial settings and restarted successfully.
4.3、藍牙AOA定位基站安裝說明（*安裝前請確認固定位置可承受 2kg 及以上的重量）
a、如右圖所示，利用 KA4 螺釘將盤架緊固安裝在平頂（箭頭所示方向）；
b、對準安裝盤架扣位，將基站推入安裝盤架卡口，盤架卡扣面標示的網口方向應與基站背面標示的網口方向一致；
c、將上級網線連接至基站 RJ45 接口（PoE IN）；
d、如果有下級級聯基站，通過網線連接該基站的RJ45接口（PoE OUT)與下級基站的RJ45接口（PoE IN），建議基站級聯不超過8級；
A, as shown in the figure on the right, use KA4 screws to firmly install the tray rack on the flat top (in the direction indicated by the arrow);
B, aiming at the mounting rack buckle position, pushing the base station into the mounting rack bayonet, and the direction of the network port marked on the rack buckle surface should be the same as that marked on the back of the base station;
C, connecting the superior network cable to the RJ45 interface (POEIN) of the base station;
D, if there is a lower cascade base station, connect the RJ45 interface (PoE OUT) of the base station with the RJ45 interface (PoEoin) of the lower base station through a network cable, and it is suggested that the cascade of the base stations should not exceed 8 levels;
4.4、藍牙AOA定位基站指示燈信號規則
a、正確安裝基站并與 PoE 交換機級聯后，基站自動啟動，啟動后可通過指示燈判定基站的運行狀況；
b、LED 指示燈的信號規則如下表所示：
A, after the base station is installed correctly and cascaded with the PoE switch, the base station automatically starts, and the operation status of the base station can be judged by the indicator light after starting;
B, the signal rules of LED indicators are shown in the following table:
亮燈狀態 |
基站狀態 |
綠燈快閃，持續 5s | 基站啟動/復位鍵長按重啟 |
紅燈快閃 | 正在獲取 IP 地址 |
綠燈慢閃 | 獲取 IP 地址成功 |
綠燈常亮 | 連接到定位引擎成功 |
紅燈常亮，持續 30s 后，基站自動復位 | 本級基站故障/未連接 |
紅綠燈交替慢閃 | 級聯的下級基站故障 |
燈暗 | 無電源連接 |
c、RJ45 接口指示燈的信號規則如下表所示：
亮燈狀態 |
基站狀態 |
常亮 | 接口有網絡連接 |
閃爍 | 接口有數據傳輸 |
燈暗 | 無網絡連接 |
4.5、藍牙AOA定位基站指示燈信號規則
a、藍牙AOA定位基站選擇 PoE 供電方式時， 必須使用的標準 PoE 供電設備進行 供電(符合 IEEE802.3af/802.3at 協議的 PSE 設備)；
b、藍牙AOA定位基站工作環境條件為 -20℃ - 60℃，濕度 0-95%，可室外安裝，殼體防 護等級 IP66，遠離火源及強電磁干擾源；
c、支持Web端， IOS和Android 平臺的上層應用開發；
d、安裝仰角理論極限 66°，強烈建議不超過 45°；
A、When the Bluetooth AOA positioning base station selects the PoE power supply mode, it must use the specified standard PoE power supply equipment (PSE equipment conforming to the IEEE802.3af/802.3at protocol) for power supply;
B、The working environment of Bluetooth AOA positioning base station is -20℃-60℃ and the humidity is 0-95%, and it can be installed outdoors. The protection level of the shell is IP66, away from fire sources and strong electromagnetic interference sources;
C、Support the upper application development of Web, IOS and Android platforms;
D、the theoretical limit of installation elevation angle is 66, and it is strongly recommended not to exceed 45;
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
智慧城市網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
