200P型減壓閥

【200P型水用減壓閥】作用

200P型水用減壓閥通過調節調節彈簧壓力設定出口壓力，上海申弘閥門有限公司主營閥門有：減壓閥(氣體減壓閥,可調式減壓閥,波紋管減壓閥,活塞式減壓閥,蒸汽減壓閥,先導式減壓閥,空氣減壓閥,氮氣減壓閥,水用減壓閥,自力式減壓閥,比例減壓閥)、安全閥、保溫閥、低溫閥、球閥、截止閥、閘閥、止回閥、蝶閥、過濾器、放料閥、隔膜閥、旋塞閥、柱塞閥、平衡閥、調節閥、疏水閥、管夾閥、排污閥、排氣閥、排泥閥、氣動閥門、電動閥門、高壓閥門、中壓閥門、低壓閥門、水力控制閥、真空閥門、襯膠閥門、襯氟閥門。利用膜片傳感出口壓力變化，通過導閥啟閉驅動活塞調節主閥節流部位過流面積的大小，實現減壓穩壓功能。200P型水用減壓閥本系列減壓閥屬于先導活塞式減壓閥。200P型水用減壓閥由主閥和導閥兩部分組成。 200P型水用減壓閥主閥主要由閥座、主閥盤、活塞、缸套、彈簧等零件組成。200P型水用減壓閥導閥主要由閥座、閥瓣、膜片、彈簧、調節彈簧等零件組成。通過調節調節彈簧壓力設定出口壓力，利用膜片傳感出口壓力變化，200P型水用減壓閥通過導閥啟閉驅動活塞調節主閥節流部位過流面積的大小，實現減壓穩壓功能。200P型水用減壓閥本產品主要用于蒸汽管路，起減壓穩壓作用。
減壓閥是一種自動降低管路工作壓力的專門裝置，它可將閥前管路較高的水壓減少至閥后管路所需的水平。從流體力學的觀點看，減壓閥是一個局部阻力可以變化的節流元件，即通過改變節流面積，使流速及流體的動能改變，造成不同的壓力損失，從而達到減壓的目的。然后依靠控制與調節系統的調節，使閥后壓力的波動與彈簧力相平衡，使閥后壓力在一定的誤差范圍內保持恒定。
減壓閥
（1） 調壓范圍：它是指減壓閥輸出壓力P2的可調范圍，在此范圍內要求達到規定的精度。調壓范圍主要與調壓彈簧的剛度有關。 
（2） 壓力特性：它是指流量g為定值時，因輸入壓力波動而引起輸出壓力波動的特性。輸出壓力波動越小，減壓閥的特性越好。輸出壓力必須低于輸入壓力—定值才基本上不隨輸入壓力變化而變化。 
（3） 流量特性：它是指輸入壓力—定時，輸出壓力隨輸出流量g的變化而變化的持性。當流量g發生變化時，輸出壓力的變化越小越好。一般輸出壓力越低，它隨輸出流量的變化波動就越小。

 
【200P型水用減壓閥】主要技術參數和性能指標

【200P型水用減壓閥】主要零件材料

【200P型水用減壓閥】流量系數（Cv）

減壓閥標準一覽表 
標準編號  標準中文名稱  標準英文名稱  JB/T10367-2002  液壓減壓閥      GB/T12245-1989  減壓閥性能試驗方法  Methods of performance test for pressure reducing valves GB/T12246-1989  先導式減壓閥  Pilot-operated reducing valves  GB/T12244-1989  減壓閥一般要求  General specification for pressure reducing valves GB/T1852-1993  船用法蘭鑄鋼蒸汽減壓閥  Marine steel flanged steam pressure reducing valves  GB10868-1989  電站減溫減壓閥技術條件   Specification of the steam converting valve for fossil power stations JB/T7376-1994(2005復審)   氣動空氣減壓閥 技術條件       JB/T7310-1994(2005復審)   裝載機用減壓閥式先導閥     JB/T53361-1994  液壓減壓閥產品質量分等(試行)    JB/T53265-1999  先導式減壓閥 產品質量分等     JB/T2205-2000  減壓閥結構長度       NF P43-035-2000   建筑閥門.供水減壓閥和復合供水減壓閥.要求和試驗   (Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests.)  NF A84-420-1991   氣焊設備和有關方法.減壓閥入品接頭.尺寸   (Equipment for gas welding and allied processes. Pressure regulators inlet connections. Dimensions.)  NF M88-773-1981   商用丁烷容器裝置.低壓固定調節的家用商品丁烷減壓閥   (INSTALLATIONS BURNING COMMERCIAL BUTANE. PRESSURE REGULATOR TRIP,LOW-PRESSURE FIXED FLOW,FOR COMMERCIAL BUTANE FOR DOMESTIC USE.)  NF M88-775-1990   裝液態碳氫化合物的鋼瓶.可移動部分和半移動部分用高壓可調減壓閥.功能.標記、試驗   (LIQUEFIED HYDROCARBONS SYSTEMS IN CYLINDERS. FIXED  ADJUSTEMENT,HIGH PRESSURE REGULATOR FOR AND SEMI- PREMISES. CONSTRUCTION. OPERATION, MARKING,TESTS.)  NF M88-737-2003   可運輸可再填充液化石油氣瓶用減壓閥   (Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG).)  NF E48-423-2001   液壓傳動.減壓閥、順序閥、卸載閥、 節流閥和止回閥.裝配面   (Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves -  Mounting surfaces.)  ANSI/ASSE 1003-1995  家用供水系統用減壓閥  (Water Pressure Reducing Valves for Domestic Water Supply Systems)  ANSI/ASSE 1046-1990  熱膨脹減壓閥  (Thermal Expansion Relief Valve)  ANSI Z 21.22a-1999  減壓閥和真空減壓閥  (Pressure Relief Valves and Vacuum Relief Valves)  ANSI Z 21.22b-2001  熱水供應系統的減壓閥  (Relief Valves for Hot Water Supply Systems (same as CSA 4.4b))  ANSI/ASTM F 1508-1997   用于蒸汽、氣體和液體設備的角型減壓閥規范   (Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services)  ASME A112.4.1-1993  熱水器減壓閥排水管  (Water heater relief valve drain tubes) ASME PTC 25.3-1988  安全和減壓閥   (Safety and relief valves) 

ASTM E 1008-2003  地熱和其它高溫液體設備用減壓閥體的安裝、檢驗及維修用標準實施規范   (Standard Practice for Installation, Inspection, and Maintenance  of Valve-body Pressure-relief Methods for Geothermal and Other  High-Temperature Liquid Applications)  標準編號  標準中文名稱  標準英文名稱  ASTM F 1795-2000   空氣或氮氣系統用減壓閥標準規范   (Standard Specification for Pressure-Reducing Valves for Air or Nitrogen Systems)  ASTM F 1565-2000  蒸汽設備用減壓閥標準規范   (Standard Specification for Pressure-Reducing Valves for Steam Service)  ASTM F 1508-1996   用于蒸汽、氣體和液體設備的角型減壓閥標準規范   (Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas and Liquid Services) ASTM F 1370-1992   船上給水系統用減壓閥   (Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard)  BS EN 1567-2000   建筑物閥門.減壓閥和組合減壓閥.要求和試驗   (Building valves - Water pressure reducing valves and combination water reducing valves - Requirements and tests)  BS ISO 5781-2000   液壓傳動.減壓閥、順序閥、卸荷閥、節流閥和止回閥.安裝面   (Hydraulic fluid power - Pressure reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces)  BS ISO 6264-1998  液壓傳動.減壓閥.裝配面   (Hydraulic fluid power - Pressure-relief valves - Mounting surfaces)  prEN 14071-2000   液化石油氣（LPG）罐的減壓閥 輔助設備   Pressure relief valves for LPG tanks - Ancillary equipment  BS 6283-2-1991   熱水系統中使用的安全和控制裝置.壓力范圍從1bar到10bar溫度減壓閥規范   (Safety and control devices for use in hot water systems  - Specifications for temperature relief valves for pressures from 1 bar to 10 bar)  BS 6283-4-1991   熱水系統中使用的安全和控制裝置.第 4部分:zui大供給壓力為12bar,標準尺寸包括DN50的微量繃緊減壓閥規范   (Safety and control devices for use in hot water systems - Specification for drop-tight pressure reducing valves of nominal size up to and including DN 50 for supply pressures up to and including 12 ba)  DIN EN 13953-2003   液化石油氣(LPG)用可運輸的可再充式儲氣瓶的減壓閥   (Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG); German version EN 13953:2003)  DIN EN 1567-2000   建筑閥門.水減壓閥和組合水減壓閥.要求和試驗   (Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests; German version EN 1567:1999) JIS B8652-2002   比例電動液壓減壓閥及安全閥的試驗方法   (Test methods for electro-hydraulic proportional pressure relief valves and electro-hydraulic  proportional pressure reducing and relieving valves)  JIS F0504-1989  船上機械裝置用減壓閥的應用和壓力調節  (Application and setting pressure of relief valves for ships' machinery)  UL 1478-1995  消防泵減壓閥   (Fire pumps relief valves )  UL 1468-1995   防火設備用直接控制的減壓閥和壓力(Direct acting pressure reducing and pressure 
控制閥   restricting valves )  JIS B8666-2001  液壓動力.減壓閥.安裝表面  (Hydraulic fluid power -- Pressure-relief valves -- Mounting surfaces)  JIS B8372-1994   氣動裝置用減壓閥   (PRESSURE REDUCING VALVES FOR PNEUMATIC USE) JIS B8664-2001   液壓動力.壓力控制閥(不包括減壓 閥)、順序活門、釋荷閥、節流閥和止回閥.安裝表面   (Hydraulic fluid power -- Pressure-control valves (excluding pressure-relief valves), sequence valves, unloading valves, throttle valves and check valves -- Mounting surfaces)  JIS B8410 AMD 1-2003  水管用減壓閥(修改件1)  (Pressure reducing valves for water works (Amendment 1))  JIS B8651-2002  比例電動液壓減壓閥試驗方法  (Test methods for electro-hydraulic proportional pressure relief valves)  JIS B8410-1999   水管用減壓閥   (Pressure reducing valves for water works) ISO 15500-12-2001   道路車輛.壓縮天然氣(CNG)燃料系統元部件.第12部分:減壓閥   (Road vehicles - Compressed natural gas (CNG) fuel system components - Part 12: Pressure relief valve (PRV))  ISO 6264-1998  液壓傳動.減壓閥.裝配面   (Hydraulic fluid power - Pressure-relief valves - Mounting surfaces)  ISO 5781-2000   液壓傳動.減壓閥、順序閥、卸荷閥、節流閥和止回閥.裝配面  (Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces) GB/T10868-2005   電站減溫減壓閥